Dijkstra's algorithm finds single-source shortest paths in a directed graph with non-negative edge weights. (When negative-weight edges are allowed, the Bellman–Ford algorithm must be used instead.) It is the algorithm of choice for solving this problem, because it is easy to understand, relatively easy to code, and, so far, the fastest algorithm known for solving this problem in the general case. In sparse graphs, running it once on every vertex to generate all-pairs shortest paths is faster than solving the same problem with the Floyd–Warshall algorithm. (The precise time complexity of Dijkstra's depends on the nature of the data structures used; read on.)
Theory of the algorithm
Dijkstra's may be characterized as a greedy algorithm, which builds the shortest-paths tree one edge at a time, adding vertices in non-decreasing order of their distance from the source. That is, in each step of the algorithm, we will find the next-closest vertex to the source. (If there is a tie, it does not matter which one is chosen.) We assume below that all nodes are reachable from the source. (If you find the two sections below too difficult, skip them.)
Suppose that we are given a set of vertices, containing the source s. We shall call a path admissible if it starts at s, proceeds through a sequence of vertices contained within , and ends with a single non- vertex. We claim that there exists an admissible path such that no other path from s to a non- vertex is shorter.
Proof: This consists of nothing but a series of observations. First, any path from s to a vertex v outside contains at least one edge from a vertex in to one outside, since s ∈ . Second, if the first such edge encountered along the path from s is not the last edge in the path, we can "cut off" the path at that point to obtain a path from s out of that is not longer (since all edges have non-negative weights). Third, if the sub-path from s to the last vertex in , denoted u, is not itself a shortest path from s to u, the length of the whole path may be decreased by substituting a shortest path from s to u for the current one. Now, suppose the opposite of what we want to prove: the shortest path from s out of , or all the shortest paths from s out of , is/are inadmissible. Then we may construct an admissible path using the three observations above which is not longer, a contradiction.
The preceding Lemma should give us an idea of how to proceed. We start with only the source vertex in the shortest-paths tree ( is merely the vertex set of the partial shortest-paths tree); its distance to itself is obviously zero. Then, we repeatedly apply the Lemma by considering all admissible paths and finding the shortest. To do this we consider all edges that lead from a vertex u to a non- vertex v. Concatenating the s-u shortest path and the u-v edge yields an admissible path whose length is the sum of the length of the already-known s-u path and the weight of the u-v edge. The edge and vertex v at the very end of the shortest admissible path are added to the shortest-paths tree (and thus v is added to ); as no path from s to a non- vertex can be shorter, we are justified in claiming that v is the closest non- vertex to s, and that its distance from s is the shortest obtainable from an admissible path currently. This method of extending the shortest-paths tree by one vertex is repeated until all vertices have been added, and induction proves the algorithm's validity. (The extension can always be performed because otherwise the remaining vertices would be unreachable from the source, a contradiction.)
As the previous sections are a bit heavy, here is some pseudocode for Dijkstra's algorithm:
input G,s for each v ∈ V(G) let dist[v] = ∞ let dist[s] = 0 let T = ∅ while T ≠ V(G) let v ∈ V(G)\T such that dist[v] is minimal add v to T for each w ∈ V(G) such that (v,w) ∈ E(G) dist[w] = min(dist[w],dist[v]+wt(v,w))
Following the completion of this code, the
dist array will contain the minimum path lengths from
s to each vertex, or if no such path exists for a given vertex.
In each iteration the inner loop will add a vertex to , so at most iterations will take place; in each one it takes time to find the vertex with the minimal
dist entry. The inner loop executes at most times, since it considers each edge at most twice (once from each endpoint). A naive implementation therefore takes time. In a dense graph, this is asymptotically optimal.
This implementation allows us to make optimizations, and more closely follows the theory, but requires a data structure
input G,s for each v ∈ V(G) let dist[v] = ∞ add (s,0) to Q while Q is nonempty let (v,d) ∈ Q such that d is minimal remove (v,d) from Q if dist[v] = ∞ dist[v] = d for each w ∈ V(G) such that (v,w) ∈ E(G) add (w,d+wt(v,w)) to Q
Each iteration of the main loop is again an iteration of the Lemma. is now implicit; it consists of all vertices with current distance (
dist value) less than infinity. The data structure
Q contains nodes that should potentially be explored next; it contains all nodes that are reachable from a single edge out of . Selecting the closest one at each iteration, we eventually explore the entire connected component and compute all shortest paths.
The data structure
Q is a priority queue ADT. If we use the binary heap implementation, then insertion and removal both take time, whereas querying the minimal element takes constant time. At most edges are inserted and at most deletions occur, which gives a time bound of . We assume the graph has no duplicate edges, so that , and then , giving the oft-quoted time bound. Hence this implementation outperforms the first in a sparse graph, and running it once per vertex to obtain all-pairs shortest paths outperforms the Floyd–Warshall algorithm in sparse graphs.
Using a Fibonacci heap implementation, which supports amortized constant time insertion, we can improve this to .
Singly constrained variant
Dijkstra's algorithm can solve the singly constrained shortest path problem. In this problem, each edge has two nonnegative weights, a length and a cost, and we wish to minimize path length subject to the constraint that the total cost must not exceed . The code looks very similar:
input G,s for each v ∈ V(G) let dist[v] = ∞ let mincost[v] = ∞ add (s,0,0) to Q while Q is nonempty let (v,d,c) ∈ Q such that c is minimal remove (v,d,c) from Q if d < dist[v] dist[v] = d for each w ∈ V(G) such that (v,w) ∈ E(G) and c + cost(v,w) ≤ C add (w,d+wt(v,w),c+cost(v,w)) to Q
Following completion of this code, the
dist array holds the minimum path lengths found, and the
mincost array holds the cost, for each vertex, required to achieve the minimum distance.
- Cormen, Thomas H.; Leiserson, Charles E.; Rivest, Ronald L.; Stein, Clifford (2001). "Section 24.3: Dijkstra's algorithm". Introduction to Algorithms (Second ed.). MIT Press and McGraw-Hill. pp. 595–601. ISBN 0-262-03293-7.